Other

Bulk packaged, corrosion resistant stainless steel fasteners.

Bulk packaged, corrosion resistant stainless steel fasteners.

Bulk packaged, corrosion resistant stainless steel fasteners.

Bulk packaged, corrosion resistant stainless steel fasteners.

Button Head Cap Screw - Stainless steel - Sold 50 per container

Button Head Cap Screw - Stainless steel - Sold 50 per container

Wave Washers for adjusting bearing play in bottom brackets.

These clamp sets can be used on any of the Thomson Seatpost line (Elite, Masterpiece, & Droppers)

This fine pair of Surly 10/12 Adapter Washers is designed to adapt any 135, 170, or 190mm O.L.D. QR axle hub with a 142, 177 or 197mm spaced thru-axle frame. Make sure the QR axle on your wheel is the right length for the frame spacing. For instance: 190mm OLD QR goes with 197mm thru-axle spacing.

One of the coolest things about Surly is if they can't find an existing part that fits their standards, they just make one themselves. This cable hanger is made to fit around the oversize bolt on their Constrictor seatpost clamp so you can be sure it will fit around almost any other seatpost clamp bolt too. It comes complete with an adjusting barrel.

If you're suffering from a slipping seatpost, Surly has the remedy. The Constrictor Seatpost Clamp grabs your post tight and hangs on for dear life. It's machined from anodized aluminum billet, uses an 8mm bolt for ultimate strength, and can accommodate a rear cantilever brake hanger.

Replacement dropout screws for the Surly Cross Check. - Bolt length: 40mm

Hurdy Gurdy is another nifty device that keeps a rear wheel from slipping forward in the dropout under pedal load. It's designed for the Cross-Check's semi-horizontal front-loading dropouts, and will also work on many other similar dropouts. Hurdy Gurdy is investment cast of stainless steel for durability and good looks, and shares many of Tuggnut's design features. Its two axle holes allow for a wide variety of fore/aft wheel positions, it will work with standard QRs, bolted axles, and nutted axles up to 10mm.

Whether for derailleur clamp clearance, tire clearance, or personal preference, sometimes it can be advantageous to run the wheel further back in the dropouts. Monkey Nuts install into Surly horizontal dropouts to make spacing the wheel back easy. There are 3 different sets depending on the type of dropout and axle configuration the dropout is intended for. Simply select the correct version of Monkey Nut, install it into the frame, and slam the wheel all the way forward. Bang, done.

Surly Monkey Nuts v3 Dropout Spacers let you keep that rear wheel nice 'n' perpendicular in those horizontal dropouts, no matter how much of a diesel you are. So go ahead, stomp on the pedals and let the rooster tails fly. They're sold individually because most folks only need one on the drive side.

Like some of Surly's other chain tensioning devices, Snuggnut keeps your rear wheel from slipping forward in the dropout under the pedal load of your powerful gams. It's specifically designed for bikes that feature 12mm horizontal, vertical-slotted dropouts and is particularly suited for singlespeed application. Snuggnut is CNC-machined for durability and good looks, and shares many design features found on Tuggnut and Hurdy Gurdy. Note: The Snuggnut is compatible with horizontal thru-axle dropouts only. If using 10/12 Adapter Washers and QR wheels use a Tuggnut instead. Snuggnut is not for use with MDS Chips. Compatible models listed below: - Wednesday - ECR 29+ - ECR 27.5+ - Ogre - Krampus - Karate Monkey SS - Karate Monkey 27.5

Rated fully KICKASS by a very authoritative entity who will remain unnamed, Surly's cast and polished stainless steel clamps won't rust or chip paint because they can't (even the black ones!). They're shiny! They look good! And most importantly, they deliver the clampability seatposts crave.

Replacement dropout screws for the Surly Straggler. - Bolt length: 40mm

Surly Thru-Axles are low-profile, bolted Thru-Axles are specifically designed for use with Surly thru-axle compatible frames. Offered in several sizes, for both front and rear wheels. 12x142 Rear Thru Axle: - Fits: Midnight Special and MDS Dropout bikes including Instigator, Legacy Karate Monkey & Legacy Krampus. 12x142/148 Rear Thru Axle: - Designed for frames with Surly Gnot Boost spacing (145mm), capable of working with 142 or 148mm rear hubs - Fits: Karate Monkey, Krampus, Troll, Ogre, ECR 12x177 Rear Thru Axle: - Fits: Wednesday 12x197 Rear Thru Axle: - Fits: Ice Cream Truck, Big Fat Dummy 12x100 Front Thru Axle: - Fits: Midnight Special 15x110 Front Thru Axle: - Fits: Karate Monkey, Krampus 15x150 Front Thru Axle: - Fits: Wednesday, Ice Cream Truck, Big Fat Dummy

Surly Stainless Steel Track Lockring. - Fits all but Campagnolo, Miche or Phil Wood - 5mm thick with 0.65mm lip for maximum thread and lockring wrench contact

A well-exercised dog is a happy dog, so give Fido a good workout while you ride! Sunlite's Dog Leash consists of a metal bar that mounts under the rear axle bolt or quick-release and straps to your chainstay. This keeps the center of gravity low so you stay stable if your dog pulls to one side. The bar is long enough to keep your pup away from the bike, too.

- Alloy construction - Great for Cruiser or BMX bar conversions

Adjustable spring rate coil that's also progressive. Sprindex is specifically designed to have a progressive spring rate for the last 20% of stroke for big hit support and for bikes with a linear linkage design. - Adjustable spring rate - Adapters included for different size shocks and set ups - Made of super high tensile spring steel

- Replacement chain pin for 7- and 8-speed Shimano chains - 3 replacement pins per pack

Beautifully machined and hand-friendly, Salsa's Flip-Off Quick-Release Skewer is a great way to keep your wheel attached to your bike. It's constructed from stainless steel to make sure it'll be along for the ride for years to come. This QR works with 170mm fatbike rear hubs.

Lip-Locks secure your seatpost and add functional bling to your ride. - Non-quick release version of the Flip-Lock - Machined 6061-AL with stainless steel pivot and bolt - Anodized with laser-etched logo - For smooth operation, lightly grease the bolt threads

Clamp allows use of a braze-on derailleur on frames without the braze-on tab. Includes a tab to use SRAM's lightweight and easy-to-adjust chain control device. - Fits all SRAM road braze-on front derailleurs - ChainSpotter not included

Disc Brake Adaptors - Includes Stainless Bolts

Power Links provide tool free chain assembly. - 8-speed width: 7.1mm - 9-speed width: 6.8mm - Chain Compatibility: SRAM - Reusable: Yes

Power links provide tool free chain assembly. - Chain Compatibility: SRAM - Reusable: No

These are the correct connecting links for SRAM's 12-speed Eagle chains. They are great for installing new chains and fixing chains on the road and trail, too. They come in a four pack, for use with four chains.

The SRAM Universal Derailleur Hanger (UDH) consolidates thousands of hanger options across the industry, while protecting your derailleur against chain jams by pivoting back and out of the way, and slipping slightly when encountering impacts. It improves shifting performance, guarantees better alignment, and works with all drivetrains. - The Universal Derailleur Hanger consolidates thousands of mountain bike derailleur standards - UDH is designed to rotate rearward in the event of impact, and features the ability to “re-rail” the chain back onto the small cog - It works with all commercially available MTB and E-MTB drivetrains from Shimano to Box to Sunrace

RockShox's Maxle Lite is a lightweight aluminum through-axle system. It lets you remove and install your wheel as fast as with a standard quick-release while delivering the awesome stiffness with the improved strength and control of a through-axle. Plus, the lever can be closed in whatever position you like and no tools are required for installation and use!

- Break-Away Quick Disconnect - Two pieces: front derailleur / rear derailleur - Time-saving system for managing derailleur cables on Break-Away bikes - Light, threaded, alloy barrels with rubber noise dampener

- Time saving system for managing brake cables on Break-Away bikes - Light threaded alloy barrels with rubber noise dampener

For use with Ritchey 12mm thru-axle forks - M12 - 1.0mm pitch - 120mm length - 7075 Alloy - 6mm hex head - 33g

The Problem Solvers Brake Boss Plugs are perfect for when you've removed your cantilever or linear-pull brakes in order to run disc brakes or a fixie setup. These plugs thread into the empty frame bosses and lend a clean look, while also protecting the threads inside the frame from corrosion.

The Problem Solvers Braze-On Front Derailleur Adapter simply clamps onto your frame's seat tube and provides a secure place to bolt on your braze-on front derailleur (sold separately). This fine adapter is made of light, durable aluminum and includes a stainless-steel bolt.

The Problem Solvers Cable Doublers are made of light, durable machined and anodized aluminum and they are Teflon coated for a super-smooth cable pull every time. They come in two models. The first allows you to control two brakes with one lever. The second allows you to control one brake with two levers. Why? Well, there are myriad applications: tandems, cyclocross bikes, fixies, tricycles, recumbents, cycles for those with special needs, bike polo bicycles, those 4-person bikes you see on beach boulevards, and so on. You could even link both models of Cable Doublers together for the ultimate in redundancy!

The Problem Solvers Cassette Spacers are made of light and durable anodized aluminum and come in different thicknesses for correctly spacing various brand and model cassette cogs. Measure and match your spacers to choose the right width.

The Problem Solvers Center Lock Adapter Kit allows riders to use 6-bolt rotors on Shimano Center Lock compatible hubs. - Not intended to be used with rotors over 180mm in diameter - Made of extruded, CNC-machined, and broached AL-6061-T6 - Designed for use with Center Lock hubs and 6-bolt disc brake rotors

The Problem Solvers Chain Tensioner is a handy device that lets you cleanly install a derailleur on frames without a derailleur hanger. It's made of light and durable CNC-machined 6061 aluminum with steel hardware. It's designed for use with rear-facing horizontal dropouts and 10mm rear axles.

The Problem Solvers Clamp-On Water Bottle Cage Mount makes it easy to carry a bottle on your handlebars so you can have even more refreshment on rides. It also comes in useful on frames without room for bottles, like smaller frames and some kid’s bikes.

The Problem Solvers Compression Plug for 1 1/8-inch Forks is for threadless aluminum and carbon forks. It fits tightly inside the fork and provides easy headset adjustment and a nice, clean look.

The Problem Solvers Double Chainring Bolts include 5 chainring bolts and nuts that are 8mm wide. This is the right size for most double-chainring setups. These chainring bolts are made of either aluminum, stainless steel, or chromoly.

Problem Solvers Pog top caps are machined aluminum with a 5 or 10mm spacer integrated as one piece. This makes for a clean, finished look when mounting a stem below the top of the steerer tube. - Bolt not included - 10mm available with or without logo - 5mm available without logo only

Problem Solvers Universal Derailleur Hangers The Universal Hanger replaces the drive-side nut on the quick-release skewer so you can get the majority of your gear range back. A vital tool to bring along when touring. - Emergency, on-the-trail derailleur hanger replacement - Enables you to keep riding and use the majority of your gear range - Compatible with most rear-facing-horizontal and vertical dropouts - Replaces the drive-side nut on 5mm quick-release skewers - Anti-rotation feature ensures the derailleur stays in place during use - CNC-machined AL-6061 with steel hardware

The Problem Solvers Quick-Release Nut Light Mount is an ingenious solution when your handlebars are too crowded to accept a light. This fine CNC-machined aluminum post simply screws on in place of your left, front quick-release nut to provide a great place to mount your light. Lower light mounting improves your depth perception and shows more details of the road condition ahead, too.

Notched binder bolts for frames with integrated seat collars. Details: CroMoly steel bolts Three lengths available: 16, 19 and 21mm 8mm diameter

The Problem Solvers Seatpost Shim is what you need when your seatpost is a little too small-diameter to fit tightly into your frame. It's made of light, durable aluminum and has a lip on the top so it won't slide down inside the frame during installation.

The Problem Solvers Shifter Boss Covers are perfect for covering up the down-tube shifter bosses when you're converting a frame with them to a singlespeed/fixie setup. They're made of light, durable aluminum and sport a nice polished finish.

The Problem Solvers Standard Top Cap is a light, durable aluminum top cap for threadless headsets. These caps fit all forks.

The Problem Solvers Wide Cable Carrier is 50mm wide and that lets you mount it lower than conventional hangers, which in turn provides greater leverage for additional braking power. This fine aluminum brake-cable carrier is especially handy for cyclocross brake setups. The extra clearance also makes it perfect for use with fenders.

- Anti chain-suck device - Allows the front derailleur to be adjusted for strong downshifts - If not using front derailleur the device can act as a chain guide

Origin-8's 1 1/8-inch Headset Spacers are made of lightweight and durable aluminum and come in 2mm, 5mm or 10mm thicknesses and lots of cool colors to add style to your ride. You get a bag of 10 spacers.

Origin-8's 1-inch Headset Spacers are made of lightweight and durable aluminum and come in 2mm, 5mm or 10mm thicknesses. You get a bag of 10 spacers.

- Upper cables for Odyssey's Gyro G3 (sold separately) - Universal fit. - Upper cables only.

Disc brake adaptors designed to mate Magura disc brakes with a variety of frame mounts and rotor sizes. - Includes hardware to mount adaptor to frame

MSW Seatpost Clamps keep your saddle and seatpost from moving around while you’re out riding. Tough and dependable, they’re available in polished silver or black finishes, as well as four common sizes. - MSW Seatpost Clamp - 28.6mm, Black

Use to create your desired chain length in single-speed applications. Only one half link is needed. - Non-reusable - Width: 9.4 mm - Drivetrain Speeds: 1 - Color: Black - Chain Compatibility: Shimano , SRAM , Campagnolo , Connex , KMC